There are many factors to consider when choosing a planetary reducer.If Selection is small, the reducer cannot bear the load or other conditions after running; a large selection will cause a waste of resources.Several factors to consider when choosing a planetary reducer Read More

如果我们在用行星减速机的时候有东西坏了怎么办?正在运行的行星减速机出现了一些损坏，大家都会觉得麻烦，这时候我们要怎么做呢。下面就来介绍下减少行星减速机出现损坏的方法。iHF爱合发其一般情况下行星减速机出现损坏的情况比较少，但我们也要注意以下两个问题。1、使用时严格按照操作规程来进行操作，操作人员最好是接受过减速机的岗前培训，同时要懂得安全生产操作系统知识。2、不要惊慌，机械设备操作过程中可能会出现各种问题和故障，精密零件是否准确，如果操作过程中问题及时停机，实际使用任何产品，有些问题或问题正常，所以这些问题可以及时制止，不要固执使用，所以不好，所以也非常建议使用时注意一些简单的技能，这将会更好 Read More

What if something breaks when using the planetary reducer?Pay attention to the method.In general, there are relatively few failures of the reducer of iHF Aihefa, but we can only damage the following two operating procedures, and strictly follow the operating procedures when using it.It is best for the operator to accept the pre-job training of the 2. reducer, and at the same time understand the knowledge of safe production operation.2. Various failures and failures that may occur in the process of mechanical equipment, whether the precision parts are accurate, if there are problems during the operation, panic in time, and there will be no problems during the actual operation. When using, some problems or any problems are normal, so these The product can indeed be stopped in time, do not use it, so it is not good, so it is also very recommended to use some simple skills, so that it can be better Read More

The bearing on the upper part of the reducer adopts oil immersion or forced lubrication. In order to prevent oil leakage in the direction of the lower shaft extension of the speed reducer, the sealing method adopts a combined seal. In the current selected reducer, no forced lubrication is required, and oil immersion lubrication is used. , which requires a supplementary oil tank on the upper part of the reducer, and the oil level of the supplementary tank should be higher than the position of the upper bearing of the reducer to meet the needs of bearing oil lubrication.It is worth noting that the output shaft of the reducer bears the axial force and radial force. Since the bearings of the output shaft of the reducer are installed in accordance with the routine, there are certain restrictions on receiving external forces.When there is a large external force, it is necessary to redesign the structure of the reducer and select the bearing according to the provided axial force and radial force.However, the steel rope driving wheel of the aerial man-ride vehicle is subjected to a large torque. If it is directly connected to the reducer through a coupling, the external force is much greater than the radial force and axial force limited by the standard design and the reducer with reinforced bearings.And the use of special design reducer, its cost will be greatly Read More

Helical gear reducer rolling bearing installation and removal.The assembly of the helical gear reducer bearing refers to the connection between the inner ring of the bearing and the journal, and the connection between the outer ring of the bearing and the bearing seat.The fit of general rolling bearings is that the inner ring and the shaft adopt a base hole fit.The inner ring has a certain tolerance, and the fit between the shaft and the hole is obtained by changing the tolerance of the shaft; the outer ring of the bearing and the bearing seat adopt the base shaft system, and the outer ring has a certain tolerance, and the outer ring is obtained by changing the tolerance of the bearing seat hole fit with the bearing housing.The nature of the gear reduction motor rolling bearing fit depends on the magnitude, direction and nature of the load on the bearing.According to the standard, the nature of the fit and the size of the bearing, select the assembly or disassembly process of the helical gear reducer, prepare the tools, and perform careful operations.The methods of assembly and disassembly of rolling bearings are: 1. Hammering method.The gear reduction motor hammering method is a method of assembling by applying external force to the inner or outer ring of the bearing through a copper rod or a soft metal sleeve with a hand hammer.This method is suitable for small bearings Read More

1. When in use, the connecting rod of the output shaft coupling should be fixed and ensure that the two shafts are parallel to the base.2. All equipment shafts installed on the output shaft must be installed lightly. Do not hit the output shaft with a hammer or other blunt objects to avoid damage to the bearing due to over-tight installation.3. The belt pulley and sprocket should be as close as possible to the load gear during assembly to help reduce the bending stress of the bearing.Sprockets, pulleys and other connecting shafts whose diameter does not exceed 6 times the output shaft should be used.Please cooperate with H7 tolerance when using to avoid noise and any abnormal damage to the axial plane during use.4. After the installation is completed, the surface of the output shaft can be coated with suitable anti-rust oil or anti-rust agent to protect the output shaft from rust.5. According to the power supply voltage, choose the appropriate wiring method to connect the wiring of the electrical junction box.Wrong wiring at the junction box can cause the motor to burn out.According to the rated current on the motor nameplate, 5A/m is recommended Read More